Model AZ Non-metalalic Casing Spacers

Description

AZ non-metallic casing spacers are designed for use with water and sewer pipes 3.85” to 13.75” in diameter. They are an economical alternative to banded woods skids and stainless steel bands for inserting pipes into casings. AZ spacers also eliminate the need for sand or grout filling of the annular space in the casing. All are adaptable to a wide variety of carrier pipe O.D.’s found on PVC Pressure/Sewer Pipe, DI-Ductile Iron, C-900, P.E., and IPS-Steel Pipes

Typical Application for Model AZ Casing Spacers Casing Spacers

Typical Installation
Based on 20-feet (6.0-meters) carrier pipe segments in a casing of not more than 300-feet (91.5-meters) . Consult PSI for longer casings and for concrete pipe.

Recommended Maximum Spacing
All Model AZ Isolator/Spacers should not exceed 5-feet (1.5-meters) to 8-feet (2.4-meters) center-to-center. An isolator/spacer should be placed within 2-feet (0.6-meters) on each side of a coupling or joint and within 1-foot (0.3-meters) of each end of the casing.

Benefits/Features of Model AZ Casing Spacers

• Variable O.D.’s of casing spacer to fit multiple sized space
• Manufactured from UV resistant polypropylene
• Runner heights may be interchanged or field cut to adjust for grade
• Corrosion protection - only metal components are steel bolts/nuts
• One piece molded construction for maximum load bearing
• Allen Head Bolts for improved spacer tightening

Material Specifications for Model AZ Casing Spacers

Warranty

All products are warranted against failure caused by manufacturing defects for a period of one year. Any product found to be so defective and returned within one year from date of shipment will be replaced without charge. The above warranty is made in lieu of, and we disclaim, any and all other warranties,

expressed or implied, including the warranties of merchantability and fitness for a particular purpose, and buyer agrees to accept the products without any such warranties. We hereby disclaim any obligation or liability for consequential damages, labor costs or any other claims or liabilities of any kind whatsoever.

How To Order Model AZ Casing Spacers

1. Quantity
2. Model Number = (AZ)
3. Carrier Pipe O.D. (Type and coating thickness if applicable.)
4. Casing Pipe I.D. (Type and coating thickness if applicable.)
5. Bell or Joint O.D.
6. Position Within Casing
7. Contact your local distributor or Pipeline Seal & Insulator, Inc.

Go To More Detailed Ordering Information and Sizing Charts

Distributor Locator
PSI Contacts

Typical Specifications for Model AZ Casing Spacers

Designed for 3.85” through 13.75” O.D. carrier pipes. Casing spacers shall be AZ segmented type molded in high density UV resistant polypropylene. Each spacer segment shall be a, “non-welded” molded piece designed for accommodating variable pipe O.D.’s by attachment of the required number of segments. Minimum spacer width shall be 5.2” (132mm). Runner height shall be sized correctly to provide adequate pipe support without the bell or joint contacting the casing during installation. Approved ISO 9001:2000 Manufacturer: Pipeline Seal & Insulator, Inc., Houston, Texas, U.S.A.

End Seal Specification
After insertion of the carrier pipe in the casing, the ends of the casing shall be closed by installing a PSI Model "C", Model "S" or Model "FW" casing end seal as manufactured by Pipeline Seal and Insulator, Inc., Houston, TX.

Link-Seal® End Seal Specification
(Carrier Pipe Must Be Centered Within Casing)
After insertion of the carrier pipe in the casing, the ends of the casing shall be closed by installing the Link-Seal® end seals and a 1/8" thick synthetic rubber end seal equal to the PSI Model "C" end seal. Both as manufactured by Pipeline Seal and Insulator, Inc., Houston, TX.
Disclaimer
The foregoing performance data is intended as guideline material only and is based on assumptions of general and reasonable use. Performance suitability for any specific application should be determined by the user.

Other Resources for Model AZ Casing Spacers

Casing Spacer and End Seals
Engineering Manual and Buyers Guide

A 38-page manual that includes information ranging form benefit/features to correct sizing methods to complete specifications for all PSI casing spacers - metallic and non-metallic versions included. Also included are PSI End Seals including Link-Seal® Modular Seals which may be used when the carrier pipe is centered in the casing.
File Size = 2,259KB

Related Products to Model AZ Casing Spacers

• End Seals
  Models "C" (Pull-on), "S" (Standard Pull-on, "W" (Wrap Around) and "FW" (Fire Resistant)
• Link-Seal® Modular Seals
  Link-Seal is an excellent method for enclosing the end of a casing when the pipe is center within the casing.
• Custom Insulators
  Multiple carrier spacers are used for inserting different size pipes, conduits and wires into casings.

PSI Contacts for Model AZ Casing Spacers

Pipeline Seal & Insulator, Inc.
6525 Goforth Street, Houston, TX 77021
Tel: 713-747-6948  •  Fax: 713-747-6029
Toll Free: 800-423-2410
e-mail: info@psipsi.com
Home
All Contacts
Distributor Locator
Literature Downloads (PDF)

Find the nearest Pipeline Seal and Insulator, Inc. distributor. Simply click on the above map or below and you will be directed to a page where you can input your zip code and quickly receive a response with the location of your nearest professional distributor that will provide you with pricing and delivery information.
Find your local distributor for PSI products.